************** VERSION 4.16 ****************
This firmware upgrade is for use with the Illumitrac

It is compatible with FIL-005 software

Extract the ".tar" firmware files from the zip file and copy them onto a laptop or PC connected to the Illumitrac.

Log in to the unit then go to the About page and note your unit's current software version, e.g. "FIL-005 4.12".

Go into Change Setup and navigate to Upgrade Software.  Click the "Choose File" button and browse to then select the ".tar" file matching the current software version.
For example, if your unit is currently running "FIL-005 4.12" software and you are upgrading to 4.16, you would select the "FIL-005_illumitrac_4.12-to-4.16_locked" file.

Click Open then "Upgrade".  A warning will pop up asking whether you want to proceed.  Click "OK".
At this point the upgrade file is loading.  There is no need to exit the page or click anything.  When the file has loaded, the upgrade page will exit back to Change Setup and the upgrade will proceed in the background.  After a couple of minutes the LCD will display "Reloading" and the unit will boot with the new firmware.


*** CHANGE LOG ***
## 4.16 - 2025-11-25
### Fixed
System log fills if I/O board stops responding
System log entries may be lost when clock changes


## 4.15 - 2025-10-08
### Added
Option to hide passwords in user interface

### Changed
Increased SMTP username and password lengths to 80 chars

### Fixed
SMS fails to send if > 160 chars with SIMCom modem


## 4.14 - 2025-09-15
### Fixed
History downloads fail over slow (remote) connections


## 4.13 - NOT RELEASED


## 4.12 - 2025-08-11
### Added
System recovery mechanism - emails an alarm message after system failure
Flash write failures trigger a system error/alarm
Modem IMEI displayed on About page
Serial number included in config file

### Changed
Software item code displayed on LCD instead of version hash
Updated branding
Remote session timeout increased to 10 minutes to match login timeout


## 4.11 - 2025-06-13
### Changed
Display year with four digits on LCD date/time page


## 4.10 - 2025-04014
### Added
RST ALx SMS command

### Fixed
Report generation stuck in fail loop


## 4.09 - 2025-02-13
### Added
Filesystem write failures trigger system alarms

### Fixed
Failed reports do not clean up temp files


## 4.08 - 2024-09-11
### Added
Modem signal logging
System error alarms
Email alarms in Illuminator mode
Time zone in View Settings in Illuminator mode
Config file indicates device type

### Changed
Alarm email footer

### Fixed
Lighting scenarios cannot be turned off
Illuminator keypad fails on first two attempts
Counters increment by 32768 when I/O board is power cycled
Admin PIN should turn lights off immediately
Two digit alarm number cannot be acknowledged by SMS
Input events do not wake device from off state
Alarm acknowledgement emails sent in low power mode when not enabled
Version information in config is automatically regenerated
Modem schedule should not apply in Illuminator mode
EXITSETP logged at startup


## 4.07 - 2024-08-19
### Changed
Reduced system boot and application start time

### Fixed
Location not included in SMTP From: header
Name property missing from SMTP Content-Type: header
Controls can get out of sync when ram config is cleared


## 4.06 - 2024-07-22
### Added
NTP support

### Fixed
HTTP server buffer overflow vulnerability
Wi-Fi drops out when clock changes
CSS missing for network setup in central mode
Freeze when modem turns on to send alarm


## 4.05 - 2024-06-14
### Added
Wi-Fi support


## 4.04 - 2024-04-23
### Added
Physical control status shown on the LCD in Illuminator mode
Input setup shown on Illuminator View Setup page
Counter and event rate of change and time alarms in Illuminator mode
Check and fix shared filesystem on boot

### Removed
Consumption multiplier in Illuminator mode

### Fixed
Short Illuminator Central sync response is not processed, causing SYNC ERR
Alarm names not updated in Illuminator dropdown lists


## 4.03 - 2023-12-20
### Changed
Default SMTP server and from address are now empty


## 4.02 - NOT RELEASED
### Changed
Allow admin PIN or backdoor PIN for all sensitive commands
The GPRS and GPSS SMS commands now require a space after them

### Fixed
Lighting scenario owner not notified after lights auto off
Original owner not notified after scenario is taken over
FRESTART SMS command does nothing


## 4.01 - 2023-12-05
### Changed
Dropped substates from modem state machine
Do not show username/password in SMS response to GET SMTP if authentication disabled

### Fixed
Fails to go online after GPRS command if both APNs are the same
SMS not received if WWAN cannot start
Fails to go online after 2nd GPRS command


## 4.00 - 2023-10-31
### Fixed
DHCP server ("easy connect") inactive if Ethernet not connected at boot
Filesystem fills due to multiple journals after multiple boots
